保姆级教程:用北醒TFmini-i-CAN雷达给PixHawk飞控加装‘眼睛’,实现自动避障与定高

香蕉派BPI-P2 Zero物联网开发板全解析:PoE供电与全志H3方案实战 在嵌入式系统与物联网开发领域,单板计算机因其高度集成和灵活性成为构建智能节点的核心硬件。其工作原理基于片上系统(SoC)整合处理器、内存及外设接口,通过轻量级Linux系统实现软硬件协同。这一技术价值在于为边缘计算提供了低成本、低功耗的解决方案,尤其适用于传感器数据采集、协议转换和设备控制等场景。其中,PoE(以太网供电)技术通过单根网线同步解决数据传输与设备供电,极大简化了部署复杂度。而全志H3芯片凭借其成熟的Cortex-A7架构与丰富生态,在性价比与视频处理能力间取得了良好平衡。本文聚焦于香蕉派BPI 阅读详情

从零打造智能无人机:北醒TFmini-i-CAN雷达与PixHawk飞控深度集成指南

当无人机遇到复杂环境时,如何让它像鸟儿一样自主规避障碍?北醒TFmini-i-CAN雷达与PixHawk飞控的组合,为DIY爱好者打开了低成本实现智能避障的大门。本文将带你完整走过从硬件选型到参数调试的全流程,特别针对初学者容易踩坑的环节提供实战解决方案。

1. 硬件准备与核心概念解析

1.1 关键设备选型指南

市面上的TFmini-i雷达主要分为485和CAN两种版本,我们需要特别注意选择 带CAN接口的型号 。这两种版本在物理接口和通信协议上有本质区别:

特性 CAN版本 485版本
接口类型 CAN总线 RS485串口
协议支持 Ardupilot原生兼容 需要额外转换
多设备扩展 支持最多10个并联 通常仅支持单设备
抗干扰能力 强(差分信号) 一般
典型应用 无人机避障/定高 工业测距

选购时还需确认包装清单包含1.25mm间距的7针JST连接器,若缺失需要单独购买。建议同时准备以下工具:

  • 焊台和细径焊锡(用于连接器改装)
  • 万用表(检测线路通断)
  • 12V/2A电源(测试阶段使用)
  • CAN总线终端电阻(120Ω,部分版本已内置)

1.2 CAN总线工作原理精要

理解CAN总线的工作机制能帮助排查90%的通信问题:

  • 多主架构 :所有设备平等,无需主机协调
  • 差分传输 :CAN_H和CAN_L双线抗干扰
  • 优先级仲裁 :ID值越小优先级越高
  • 终端电阻 :总线两端各需120Ω电阻消除信号反射 <
手把手教你用TFmini-i-CAN雷达给PixHawk飞控加装‘眼睛’:避障与定高保姆级配置 本文详细介绍了如何使用Benewake TFmini-i-CAN雷达为PixHawk飞控添加避障与定高功能,包括硬件准备、雷达配置、硬件连接及飞控参数设置。通过CAN总线通信,TFmini-i-CAN雷达可实现厘米级精度的避障和稳定的飞行高度控制,适用于航拍、巡检等场景。文章还提供了常见问题排查和性能优化建议,帮助开发者快速上手。 阅读详情

相关推荐

从避障到定高:北醒TFmini-i-CAN雷达与ArduPilot飞控的深度集成实践

本文详细介绍了如何将北醒TFmini-i-CAN激光雷达深度集成到ArduPilot飞控系统中,实现一机两用:既作为前方避障传感器,又作为向下定高雷达。通过硬件连接、CAN ID配置、飞控参数详细设置及实战测试,为无人机爱好者提供了从避障到厘米级精准定高的完整解决方案,特别适合植保、巡检等应用场景。

weixin_29184075的博客 398

手把手教你用TFmini-i-CAN雷达给APM飞控加装‘眼睛’:避障与定高保姆级教程

本文详细介绍了如何将TFmini-i-CAN雷达与APM飞控深度集成,实现无人机的避障与定高功能。从硬件准备、物理连接、CAN总线配置到避障算法优化,提供了一套完整的保姆级教程,特别针对PixHawk飞控与Ardupilot固件环境中的常见问题进行了重点解析,帮助飞手快速掌握雷达避障系统的部署与调试技巧。

weixin_30430169的博客 544

手把手教你用TFmini-i-CAN雷达给PixHawk飞控加装‘眼睛’:避障与定高保姆级教程

本文详细介绍了如何使用TFmini-i-CAN雷达为PixHawk飞控实现避障与定高功能,包含硬件选型、CAN指令配置、飞控连接及ArduPilot参数调试等全流程。特别针对农业植保场景中的复杂环境,提供了多雷达组网配置和典型故障排除方案,帮助开发者快速实现无人机智能避障。

weixin_30580341的博客 135

Pixhawk v1-v3硬件设计深度解析

本文深入分析Pixhawk飞控v1至v3版本的硬件设计,涵盖双MCU架构、IMU布局、电源管理、PCB布线等关键技术,揭示其高可靠性设计背后的工程智慧,适合飞控开发者与嵌入式系统学习者参考。

solidity8miner的博客 640

简单的ASP表单提交到后台的源码

这是一个简单的带后台的表单提交asp源码

asp.net控件用法 很全的哦

asp.net控件用法 常用控件用法asp.net控件用法 常用控件用法

链接、页面跳转、隐藏、表单提交

链接、页面跳转、隐藏、表单提交等的个人笔记

Apple CarPlay Certification Guide December 2022 解析V1.0

Apple CarPlay Certification Guide December 2022更新说明

m0_74450450的博客 709

Allegro17.4原理图-PCB双向联动技巧:从网表生成到同步高亮

本文深入解析了Cadence Allegro 17.4中原理图与PCB的深度双向联动技巧。核心在于通过精准的网表生成与管理、实时的跨窗口交互高亮与信号追踪,以及元件与封装的智能匹配更新,构建高效协同设计工作流。掌握这些技巧能显著提升高速、高密度电路设计的效率与准确性,实现从逻辑设计到物理实现的无缝衔接。

weixin_29178069的博客 371

Rk3568 百兆以太网RMII模式DTS配置详解

本文详细解析了RK3568芯片在百兆以太网RMII模式下的DTS配置方法,包括时钟树配置、PHY接口模式定义及实际工程中的进阶设置。通过实战案例和调试技巧,帮助开发者快速解决RMII模式下的常见问题,提升工业控制设备的网络稳定性。

weixin_29189377的博客 422

中山大学_数据科学与计算机_预推免

前言 2019 年 9 月中旬是中山大学预推免时间,本人没能进到夏令营,但是最后在预推免上岸也算不幸中的万幸。 记忆不一定准确,但希望能帮到他人。 想看 流程 的可以直接看总结,正文部分有本人心路历程。 预推免 中山大学的预推免大致可以分为 报道,机试,面试 三大部分,而且尤其是面试,所有人加起来总时长 3 天,幸运的是,本人被安排在第一天的下午第一场,上午就是机试,报道,机试,面试,无缝衔接。 ...

一把健 5211

变焦跟踪理论基础(如何在变焦过程中保持清晰)

如何在整个变焦过程中一直保持图像的清晰度或焦点是变焦跟踪的主要挑战。 当用户在缩放跟踪的情况下改变缩放时,设备保持对焦。 然而,在没有变焦跟踪的情况下,图像变得失焦,图像在变焦跟踪后由于自动对焦(AF)算法才最终对焦。...................................................

ChenYX的博客 20万+

OpenCV函数用法之calibrateCamera

参考链接:opencv中标定函数calibrateCamera_ychl87的专栏-CSDN博客 世界坐标系的三维点投影到成像坐标系中的二维点的投影公式如下: 其中(X,Y,Z)为世界坐标系中的三维点; (u,v)为成像面坐标系中的二维点; A为相机的内参数矩阵:(cx,cy)为主光轴点,一般为图像的中心;fx和fy为焦距; [R|t]为相机的外参数矩阵:R为旋转矩阵,t为位移矩阵; 上述公式的简单推理过程如下 考虑到镜头畸变 其中,k1,k2,k3,k4,k5和k6为径向畸变,p1和.

tiger&sheep的博客 3万+

MDK5 Debug调试方法总结

MDK5 Debug调试方法总结

m0_70748084的博客 2万+

OSG第三方库编译之二十一:minizip编译(Windows、Linux、Macos环境下编译)

OSG编译;第三方库;跨平台编译;minizip编译(Windows、Linux、Macos环境下编译)

LuckyHanMo的博客 2627

Outlook Express 6 (OE6) for Win7/Win8/Win10

英文版 Outlook Express6.0, 兼容Win7/Win10/WinXP,解压就可用。

精雕软件(JDpaint) 5.5 绿色版

精雕软件(JDpaint) 5.5 绿色版精雕软件(JDpaint) 5.5 绿色版精雕软件(JDpaint) 5.5 绿色版

计算机控制技术及应用

《计算机控制技术及应用》通过总结作者的科研成果和吸收国内外的先进理论、方法和技术,以计算机控制系统的网络化、开放化、智能化和集成化发展趋势为主线索,主要介绍计算机控制系统的基本概念和计算机控制系统的典型形式,计算机控制系统的数学描述与基本分析方法,以及数字PID控制器、最少拍控制系统、达林算法、状态变量设计法等设计方法及其各种改进算法。重点突出计算机控制系统输入输出通道接口的设计方法和典型控制系统的设计案例与实现方法等。

深度学习工具包 DeepLearningToolbox

深度学习工具包Deprecation notice.-----This toolbox is outdated and no longer maintained.There are much better tools available for deep learning than this toolbox, e.g. [Theano](http://deeplearning.net/software/theano/), [torch](http://torch.ch/) or [tensorflow](http://www.tensorflow.org/)I would suggest you use one of the tools mentioned above rather than use this toolbox.Best, Rasmus.DeepLearnToolbox================A Matlab toolbox for Deep Learning.Deep Learning is a new subfield of machine learning that focuses on learning deep hierarchical models of data.It is inspired by the human brain's apparent deep (layered, hierarchical) architecture.A good overview of the theory of Deep Learning theory is[Learning Deep Architectures for AI](http://www.iro.umontreal.ca/~bengioy/papers/ftml_book.pdf)For a more informal introduction, see the following videos by Geoffrey Hinton and Andrew Ng.* [The Next Generation of Neural Networks](http://www.youtube.com/watch?v=AyzOUbkUf3M) (Hinton, 2007)* [Recent Developments in Deep Learning](http://www.youtube.com/watch?v=VdIURAu1-aU) (Hinton, 2010)* [Unsupervised Feature Learning and Deep Learning](http://www.youtube.com/watch?v=ZmNOAtZIgIk) (Ng, 2011)If you use this toolbox in your research please cite [Prediction as a candidate for learning deep hierarchical models of data](http://www2.imm.dtu.dk/pubdb/views/publication_details.php?id=6284)```@MASTERSTHESIS\{IMM2012-06284, author = "R. B. Palm", title = "Prediction as a candidate for learning deep hierarchical models of data", year = "2012",}```Contact: rasmusbergpalm at gmail dot comDirectories included in the toolbox-----------------------------------`NN/` - A library for Feedforward Backpropagation Neural Networks`CNN/` - A library for Convolutional Neural Networks`DBN/` - A library for Deep Belief Networks`SAE/` - A library for Stacked Auto-Encoders`CAE/` - A library for Convolutional Auto-Encoders`util/` - Utility functions used by the libraries`data/` - Data used by the examples`tests/` - unit tests to verify toolbox is workingFor references on each library check REFS.mdSetup-----1. Download.2. addpath(genpath('DeepLearnToolbox'));Example: Deep Belief Network---------------------```matlabfunction test_example_DBNload mnist_uint8;train_x = double(train_x) / 255;test_x = double(test_x) / 255;train_y = double(train_y);test_y = double(test_y);%% ex1 train a 100 hidden unit RBM and visualize its weightsrand('state',0)dbn.sizes = [100];opts.numepochs = 1;opts.batchsize = 100;opts.momentum = 0;opts.alpha = 1;dbn = dbnsetup(dbn, train_x, opts);dbn = dbntrain(dbn, train_x, opts);figure; visualize(dbn.rbm{1}.W'); % Visualize the RBM weights%% ex2 train a 100-100 hidden unit DBN and use its weights to initialize a NNrand('state',0)%train dbndbn.sizes = [100 100];opts.numepochs = 1;opts.batchsize = 100;opts.momentum = 0;opts.alpha = 1;dbn = dbnsetup(dbn, train_x, opts);dbn = dbntrain(dbn, train_x, opts);%unfold dbn to nnnn = dbnunfoldtonn(dbn, 10);nn.activation_function = 'sigm';%train nnopts.numepochs = 1;opts.batchsize = 100;nn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.10, 'Too big error');```Example: Stacked Auto-Encoders---------------------```matlabfunction test_example_SAEload mnist_uint8;train_x = double(train_x)/255;test_x = double(test_x)/255;train_y = double(train_y);test_y = double(test_y);%% ex1 train a 100 hidden unit SDAE and use it to initialize a FFNN% Setup and train a stacked denoising autoencoder (SDAE)rand('state',0)sae = saesetup([784 100]);sae.ae{1}.activation_function = 'sigm';sae.ae{1}.learningRate = 1;sae.ae{1}.inputZeroMaskedFraction = 0.5;opts.numepochs = 1;opts.batchsize = 100;sae = saetrain(sae, train_x, opts);visualize(sae.ae{1}.W{1}(:,2:end)')% Use the SDAE to initialize a FFNNnn = nnsetup([784 100 10]);nn.activation_function = 'sigm';nn.learningRate = 1;nn.W{1} = sae.ae{1}.W{1};% Train the FFNNopts.numepochs = 1;opts.batchsize = 100;nn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.16, 'Too big error');```Example: Convolutional Neural Nets---------------------```matlabfunction test_example_CNNload mnist_uint8;train_x = double(reshape(train_x',28,28,60000))/255;test_x = double(reshape(test_x',28,28,10000))/255;train_y = double(train_y');test_y = double(test_y');%% ex1 Train a 6c-2s-12c-2s Convolutional neural network %will run 1 epoch in about 200 second and get around 11% error. %With 100 epochs you'll get around 1.2% errorrand('state',0)cnn.layers = { struct('type', 'i') %input layer struct('type', 'c', 'outputmaps', 6, 'kernelsize', 5) %convolution layer struct('type', 's', 'scale', 2) %sub sampling layer struct('type', 'c', 'outputmaps', 12, 'kernelsize', 5) %convolution layer struct('type', 's', 'scale', 2) %subsampling layer};cnn = cnnsetup(cnn, train_x, train_y);opts.alpha = 1;opts.batchsize = 50;opts.numepochs = 1;cnn = cnntrain(cnn, train_x, train_y, opts);[er, bad] = cnntest(cnn, test_x, test_y);%plot mean squared errorfigure; plot(cnn.rL);assert(er<0.12, 'Too big error');```Example: Neural Networks---------------------```matlabfunction test_example_NNload mnist_uint8;train_x = double(train_x) / 255;test_x = double(test_x) / 255;train_y = double(train_y);test_y = double(test_y);% normalize[train_x, mu, sigma] = zscore(train_x);test_x = normalize(test_x, mu, sigma);%% ex1 vanilla neural netrand('state',0)nn = nnsetup([784 100 10]);opts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samples[nn, L] = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.08, 'Too big error');%% ex2 neural net with L2 weight decayrand('state',0)nn = nnsetup([784 100 10]);nn.weightPenaltyL2 = 1e-4; % L2 weight decayopts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samplesnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex3 neural net with dropoutrand('state',0)nn = nnsetup([784 100 10]);nn.dropoutFraction = 0.5; % Dropout fraction opts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samplesnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex4 neural net with sigmoid activation functionrand('state',0)nn = nnsetup([784 100 10]);nn.activation_function = 'sigm'; % Sigmoid activation functionnn.learningRate = 1; % Sigm require a lower learning rateopts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samplesnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex5 plotting functionalityrand('state',0)nn = nnsetup([784 20 10]);opts.numepochs = 5; % Number of full sweeps through datann.output = 'softmax'; % use softmax outputopts.batchsize = 1000; % Take a mean gradient step over this many samplesopts.plot = 1; % enable plottingnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex6 neural net with sigmoid activation and plotting of validation and training error% split training data into training and validation datavx = train_x(1:10000,:);tx = train_x(10001:end,:);vy = train_y(1:10000,:);ty = train_y(10001:end,:);rand('state',0)nn = nnsetup([784 20 10]); nn.output = 'softmax'; % use softmax outputopts.numepochs = 5; % Number of full sweeps through dataopts.batchsize = 1000; % Take a mean gradient step over this many samplesopts.plot = 1; % enable plottingnn = nntrain(nn, tx, ty, opts, vx, vy); % nntrain takes validation set as last two arguments (optionally)[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');```[![Bitdeli Badge](https://d2weczhvl823v0.cloudfront.net/rasmusbergpalm/deeplearntoolbox/trend.png)](https://bitdeli.com/free "Bitdeli Badge")

上一篇: 深入解析NXP LPC51U68:ARM Cortex-M0+高能效MCU的外设与低功耗设计
下一篇: 从归并排序到逆序对:一个算法竞赛选手的思维跃迁(附洛谷P1908满分代码)
weixin_30892889
博客等级 码龄11年 152粉丝 1298原创
评论
成就一亿技术人!
拼手气红包6.0元
还能输入1000个字符  | 博主筛选后可见
 
 条评论被折叠 查看
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付:10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值
⌂ 换网址