RV1126摄像头模组移植实战:从I2C驱动到MIPI数据流的全链路解析

rv1126 camera调试常用命令 rv1126 camera调试常用命令 本文采用知识共享署名 4.0 国际许可协议进行许可,转载时请注明原文链接,图片在使用时请保留全部内容,可适当缩放并在引用处附上图片所在的文章链接。 查看图像数据的端点信息 查看系统当前DRM情况 media-ctl 反编译 dtb 文件 查看图像数据的端点信息 grep '' /sys/class/video4linux/video*/name ISP: rkisp_mainpath:视频输出 rkisp_selfpath:视频输出 rkisp-sta 阅读详情

1. 硬件接口与基础原理

摄像头模组与RV1126芯片的连接主要依赖两个关键接口:I2C和MIPI。I2C负责传感器驱动注册和配置,MIPI负责高速图像数据传输。这种分工明确的架构让调试过程更有针对性——驱动注册失败先查I2C,图像采集异常则重点排查MIPI链路。

在实际项目中,我调试过IMX258、GC2053、SC8238等多种传感器。虽然这些传感器的寄存器配置各不相同,但硬件接口原理相通。以IMX258为例,其硬件接口包含:

  • I2C通信引脚:SCL(时钟线)、SDA(数据线)
  • MIPI数据通道:通常1-4对差分信号线(Data0_P/N到Data3_P/N)
  • 时钟基准:MIPI时钟线(CLK_P/N)
  • 控制信号:复位引脚(RESET)、电源使能(PWDN)

提示:首次上电前务必用万用表测量供电电压。我曾遇到一个坑——硬件同事将1.8V电源误接为3.3V,导致传感器瞬间烧毁。常规供电包括:

  • AVDD(模拟电源):2.8V
  • DVDD(数字核心电源):1.2V
  • DOVDD(接口电源):1.8V

2. 设备树(DTS)配置详解

设备树配置是摄像头移植的核心环节,它定义了硬件连接关系和参数特性。RV1126提供两种MIPI数据链路选择:

链路1(直连ISP):

sensor → phy → rkisp_vir0

这种链路适合直接获取经过ISP处理的YUV数据,图像质量更好但延迟稍高。

链路2(经CIF处理):

sensor → phy → mipi-csi → rkcif → rkisp_vir0

这种链路适合需要获取RAW原始数据的场景,比如调试阶段的图像质量分析。

这是我常用的IMX258设备树配置片段:

&i2c1 {
    imx258: imx258@1a {
        compatible = "sony,imx258";
        reg = <0x1a>;  // I2C地址
        clocks = <&cru CLK_MIPICSI_OUT>;
        clock-names = "xvclk";
        reset-gpios = <&gpio1 RK_PD1 GPIO_ACTIVE_LOW>;
        
        port {
            ucam_out5: endpoint {
                remote-endpoint = <&csi_dphy1_input>;
                data-lanes = <1 2 3 4>;  // 使用4个数据通道
            };
        };
    };
};
IMX335摄像头驱动注册分析 由设备树可知,imx335摄像头设备其实对内核来说,是一个i2c设备,故驱动程序是以一个i2c设备形式进行驱动的注册。驱动文件路径:linux-4.19.111/drivers/media/i2c。在驱动中,中来描述一个imx335设备。 阅读详情

相关推荐

rv1126 buildroot imx415调试

在rv1126的板子上调通ov13850,但是iq没调好,显示效果没调 于是更换摄像头imx415,sdk本身自带该驱动,本想着,配置好就可以了,但是事情没有那么简单 调试了一天半才弄好。 先看imx415的上电时序 在I2C通信之前我们必须要给主时钟,也就是INCK 我们用自带的驱动,配置好后,发现I2C还是没有通信成功 然后去看驱动代码,在__imx415_power_on函数中reset的gpio没有拉高 于是添加 在数据手册中没有关于reset的时许,所以是参考ov13850

qq_32017483的博客 5588

RV1126摄像头模组移植实战:从硬件对接到图像调优

本文详细介绍了在RV1126平台上进行摄像头模组移植的完整实战流程。从硬件对接的供电、I2C与MIPI信号检查,到软件层面的DTS链路配置、驱动集成与编译,再到使用CIF链路抓取RAW数据、ISP链路获取NV12流的实战调试方法,最后提供了图像质量调优入门与常见问题避坑指南,旨在帮助开发者高效完成摄像头模组在RV1126上的适配与图像调优工作。

weixin_29189003的博客 235

保姆级教程:用RV1126的CIF和ISP双链路,搞定GC2053/IMX415摄像头Raw与NV12数据采集

本文详细解析了RV1126芯片的CIF与ISP双链路架构,通过GC2053/IMX415摄像头模组的实战案例,展示了如何高效采集Raw与NV12数据。从硬件准备、DTS配置到驱动加载与数据采集,提供了全流程的保姆级教程,帮助开发者快速掌握嵌入式视觉系统的开发技巧。

weixin_29161719的博客 201

RK3568平台 (camera篇)点亮gc2053/gc2093

第二部分和MIPI相关的,需要MIPI进行图像传输,所以驱动应该就有这一部分的驱动,这部分一般是由SOC厂家提供。第三部分就是ISP部分,有些SOC有ISP图像处理模块,经过MIPI传输的图像进入SOC之后需要在传入SOC的ISP模块对图像进一步进行加工,所以一定是有一部分驱动是描述ISP模块的。一般情况下,Camera和SOC有两个接口进行连接,分为为MIPI接口和I2C接口,其中MIPI接口用来传输图像的数据,数据传输路径为从Sensor传输到SOC。

weixin_49303682的博客 7806

IMX258图像传感器驱动开发与实战源码解析

CMOS(互补金属氧化物半导体)图像传感器是一种将光信号转换为电信号的半导体器件,具有低功耗、高集成度和成本低廉等优势。其工作原理基于光电二极管在光照下产生电荷,随后通过像素级的放大器和ADC(模数转换器)将模拟信号转化为数字信号。CMOS图像传感器广泛应用于智能手机、车载摄像头、工业视觉、无人机、安防监控、AR/VR设备等领域。随着嵌入式视觉技术的发展,对图像传感器的实时性、分辨率、功耗及接口兼容性提出了更高要求。

weixin_29097457的博客 1645

rv1126移植摄像头模组

rv1126通用性移植摄像头模组讲解,使用当前方式移植过gc2053、gc2093、imx415、sc8238、imx258等摄像头模组;

qq_46030455的博客 4223

ui(new Ui::MainWindow)的解析

Ui命名空间的变量名,和默认空间的变量名虽然一样,但实际是两个不同的东西。所以构造函数中调用MainWindow是没问题的,因为它不是在调用自身,而是在调用其他命名空间下的另一个同名的MainWindow类。这里使用C++的成员初始化列表语法,初始化成员变量指针ui,可这里有个问题,在MainWindow的构造函数中new 一个MainWindow,这又调用一下MainWindow的构造函数,这岂不是会死循环?ui_mainwindow.h文件。mainwindow.h文件.

sinat_31608641的博客 1195

大华摄像头GB28181协议接入EasyCVR全流程(附常见错误排查)

本文详细阐述了大华摄像头通过GB28181协议接入EasyCVR视频管理平台的全流程,涵盖从核心原理、前期参数规划、Web界面配置到平台侧验证的完整步骤。重点针对网络端口、SIP参数配置等关键环节提供了深度排错指南,并总结了设备无法注册、在线不稳定、拉流失败等常见问题的排查思路与解决方案,旨在帮助安防工程师与系统集成商高效完成设备接入与调试。

weixin_29279153的博客 311

VASP计算层错能(SFE)全攻略2

本文介绍了使用VASP计算纯镍(Ni)层错能(SFE)的具体步骤。首先构建Ni的FCC单胞并扩展为超胞,通过修改原子位置引入堆垛层错;随后分别计算完美晶体和含层错结构的能量;最后通过能量差与层错面积之比求得SFE值。计算需注意k点网格、截断能和超胞尺寸的收敛性测试,并推荐使用PAW赝势和ASE等工具辅助结构构建。

weixin_50519490的博客 1996

Vanna 2.0:基于LLM的智能文本到SQL框架,实现企业级数据查询与权限控制

文本到SQL技术是自然语言处理与数据库交互的重要桥梁,它允许用户使用日常语言直接查询数据库,无需编写复杂的SQL语句。其核心原理是利用大语言模型理解用户意图,并结合检索增强生成技术,将自然语言问题转换为准确的结构化查询语言。这项技术的价值在于大幅降低了数据访问门槛,提升了业务人员的数据自助分析能力,并能在金融分析、销售报表、运营监控等场景中实现实时数据洞察。Vanna 2.0作为一个开源框架,通过引入用户感知的智能体架构和行级安全策略,解决了企业级应用中的多租户数据隔离与权限控制等关键问题,使得自然语言数据

weixin_42629522的博客 551

python爬取巨潮资讯网所有股票年报数据

爬虫获取巨潮资讯网数据

qq_42752524的博客 6142

在树莓派上部署训练好的YOLO模型

.pt.模型转换为onnx格式的模型,树莓派上部署模型

pai_da_xing8的博客 3889

提示词编写:从新手到专家的进阶之路

本文旨在为提示词编写者提供一条从新手到专家的进阶之路。我们将详细探讨提示词编写的背景与意义、基础与进阶技巧、实战应用以及最佳实践。通过逐步深入的分析与实操,读者将掌握提示词编写的核心要点,提高编写效率和作品质量。提示词是用于引导人工智能生成文本的关键词或短语,它包含了作者想要传达的主题、情感和细节。随着人工智能技术的普及,自动化写作工具逐渐应用于各行各业。为了提高写作效率,项目团队决定开发一款基于人工智能的自动化写作工具。成功开发了一款自动化写作工具,生成文本质量较高。

AI天才研究院 1087

ET2012新版免狗免安装绿色软件

ET2012新版免狗免安祖昂绿色软件。,新界面,新视觉,

深度学习工具包 DeepLearningToolbox

深度学习工具包Deprecation notice.-----This toolbox is outdated and no longer maintained.There are much better tools available for deep learning than this toolbox, e.g. [Theano](http://deeplearning.net/software/theano/), [torch](http://torch.ch/) or [tensorflow](http://www.tensorflow.org/)I would suggest you use one of the tools mentioned above rather than use this toolbox.Best, Rasmus.DeepLearnToolbox================A Matlab toolbox for Deep Learning.Deep Learning is a new subfield of machine learning that focuses on learning deep hierarchical models of data.It is inspired by the human brain's apparent deep (layered, hierarchical) architecture.A good overview of the theory of Deep Learning theory is[Learning Deep Architectures for AI](http://www.iro.umontreal.ca/~bengioy/papers/ftml_book.pdf)For a more informal introduction, see the following videos by Geoffrey Hinton and Andrew Ng.* [The Next Generation of Neural Networks](http://www.youtube.com/watch?v=AyzOUbkUf3M) (Hinton, 2007)* [Recent Developments in Deep Learning](http://www.youtube.com/watch?v=VdIURAu1-aU) (Hinton, 2010)* [Unsupervised Feature Learning and Deep Learning](http://www.youtube.com/watch?v=ZmNOAtZIgIk) (Ng, 2011)If you use this toolbox in your research please cite [Prediction as a candidate for learning deep hierarchical models of data](http://www2.imm.dtu.dk/pubdb/views/publication_details.php?id=6284)```@MASTERSTHESIS\{IMM2012-06284, author = "R. B. Palm", title = "Prediction as a candidate for learning deep hierarchical models of data", year = "2012",}```Contact: rasmusbergpalm at gmail dot comDirectories included in the toolbox-----------------------------------`NN/` - A library for Feedforward Backpropagation Neural Networks`CNN/` - A library for Convolutional Neural Networks`DBN/` - A library for Deep Belief Networks`SAE/` - A library for Stacked Auto-Encoders`CAE/` - A library for Convolutional Auto-Encoders`util/` - Utility functions used by the libraries`data/` - Data used by the examples`tests/` - unit tests to verify toolbox is workingFor references on each library check REFS.mdSetup-----1. Download.2. addpath(genpath('DeepLearnToolbox'));Example: Deep Belief Network---------------------```matlabfunction test_example_DBNload mnist_uint8;train_x = double(train_x) / 255;test_x = double(test_x) / 255;train_y = double(train_y);test_y = double(test_y);%% ex1 train a 100 hidden unit RBM and visualize its weightsrand('state',0)dbn.sizes = [100];opts.numepochs = 1;opts.batchsize = 100;opts.momentum = 0;opts.alpha = 1;dbn = dbnsetup(dbn, train_x, opts);dbn = dbntrain(dbn, train_x, opts);figure; visualize(dbn.rbm{1}.W'); % Visualize the RBM weights%% ex2 train a 100-100 hidden unit DBN and use its weights to initialize a NNrand('state',0)%train dbndbn.sizes = [100 100];opts.numepochs = 1;opts.batchsize = 100;opts.momentum = 0;opts.alpha = 1;dbn = dbnsetup(dbn, train_x, opts);dbn = dbntrain(dbn, train_x, opts);%unfold dbn to nnnn = dbnunfoldtonn(dbn, 10);nn.activation_function = 'sigm';%train nnopts.numepochs = 1;opts.batchsize = 100;nn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.10, 'Too big error');```Example: Stacked Auto-Encoders---------------------```matlabfunction test_example_SAEload mnist_uint8;train_x = double(train_x)/255;test_x = double(test_x)/255;train_y = double(train_y);test_y = double(test_y);%% ex1 train a 100 hidden unit SDAE and use it to initialize a FFNN% Setup and train a stacked denoising autoencoder (SDAE)rand('state',0)sae = saesetup([784 100]);sae.ae{1}.activation_function = 'sigm';sae.ae{1}.learningRate = 1;sae.ae{1}.inputZeroMaskedFraction = 0.5;opts.numepochs = 1;opts.batchsize = 100;sae = saetrain(sae, train_x, opts);visualize(sae.ae{1}.W{1}(:,2:end)')% Use the SDAE to initialize a FFNNnn = nnsetup([784 100 10]);nn.activation_function = 'sigm';nn.learningRate = 1;nn.W{1} = sae.ae{1}.W{1};% Train the FFNNopts.numepochs = 1;opts.batchsize = 100;nn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.16, 'Too big error');```Example: Convolutional Neural Nets---------------------```matlabfunction test_example_CNNload mnist_uint8;train_x = double(reshape(train_x',28,28,60000))/255;test_x = double(reshape(test_x',28,28,10000))/255;train_y = double(train_y');test_y = double(test_y');%% ex1 Train a 6c-2s-12c-2s Convolutional neural network %will run 1 epoch in about 200 second and get around 11% error. %With 100 epochs you'll get around 1.2% errorrand('state',0)cnn.layers = { struct('type', 'i') %input layer struct('type', 'c', 'outputmaps', 6, 'kernelsize', 5) %convolution layer struct('type', 's', 'scale', 2) %sub sampling layer struct('type', 'c', 'outputmaps', 12, 'kernelsize', 5) %convolution layer struct('type', 's', 'scale', 2) %subsampling layer};cnn = cnnsetup(cnn, train_x, train_y);opts.alpha = 1;opts.batchsize = 50;opts.numepochs = 1;cnn = cnntrain(cnn, train_x, train_y, opts);[er, bad] = cnntest(cnn, test_x, test_y);%plot mean squared errorfigure; plot(cnn.rL);assert(er<0.12, 'Too big error');```Example: Neural Networks---------------------```matlabfunction test_example_NNload mnist_uint8;train_x = double(train_x) / 255;test_x = double(test_x) / 255;train_y = double(train_y);test_y = double(test_y);% normalize[train_x, mu, sigma] = zscore(train_x);test_x = normalize(test_x, mu, sigma);%% ex1 vanilla neural netrand('state',0)nn = nnsetup([784 100 10]);opts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samples[nn, L] = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.08, 'Too big error');%% ex2 neural net with L2 weight decayrand('state',0)nn = nnsetup([784 100 10]);nn.weightPenaltyL2 = 1e-4; % L2 weight decayopts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samplesnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex3 neural net with dropoutrand('state',0)nn = nnsetup([784 100 10]);nn.dropoutFraction = 0.5; % Dropout fraction opts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samplesnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex4 neural net with sigmoid activation functionrand('state',0)nn = nnsetup([784 100 10]);nn.activation_function = 'sigm'; % Sigmoid activation functionnn.learningRate = 1; % Sigm require a lower learning rateopts.numepochs = 1; % Number of full sweeps through dataopts.batchsize = 100; % Take a mean gradient step over this many samplesnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex5 plotting functionalityrand('state',0)nn = nnsetup([784 20 10]);opts.numepochs = 5; % Number of full sweeps through datann.output = 'softmax'; % use softmax outputopts.batchsize = 1000; % Take a mean gradient step over this many samplesopts.plot = 1; % enable plottingnn = nntrain(nn, train_x, train_y, opts);[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');%% ex6 neural net with sigmoid activation and plotting of validation and training error% split training data into training and validation datavx = train_x(1:10000,:);tx = train_x(10001:end,:);vy = train_y(1:10000,:);ty = train_y(10001:end,:);rand('state',0)nn = nnsetup([784 20 10]); nn.output = 'softmax'; % use softmax outputopts.numepochs = 5; % Number of full sweeps through dataopts.batchsize = 1000; % Take a mean gradient step over this many samplesopts.plot = 1; % enable plottingnn = nntrain(nn, tx, ty, opts, vx, vy); % nntrain takes validation set as last two arguments (optionally)[er, bad] = nntest(nn, test_x, test_y);assert(er < 0.1, 'Too big error');```[![Bitdeli Badge](https://d2weczhvl823v0.cloudfront.net/rasmusbergpalm/deeplearntoolbox/trend.png)](https://bitdeli.com/free "Bitdeli Badge")

LinePhone3.2.7(android端最新版本) sip客户端

SIP客户端For android:LinePhone3.2.7(最新版本),官网地址:http://www.linphone.org/

迈瑞BS系列全自动生化分析仪LIS协议接口手册(内含HL7和ASTM)

迈瑞BS系列全自动生化分析仪LIS协议接口手册,内含HL7和ASTM)

上一篇: 智能晾衣架背后的通信协议:深入解析I²C与红外NEC在物联网中的应用
下一篇: 跨越陷阱:ADS131A04开发中的十大常见误区与避坑指南
雪落无声360
博客等级 码龄4年 995粉丝 1491原创
评论
成就一亿技术人!
拼手气红包6.0元
还能输入1000个字符  | 博主筛选后可见
 
 条评论被折叠 查看
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付:10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值
⌂ 换网址